The experienced detectorists at Minelab have put together a comprehensive list of FAQs on how to use a metal detector. These also contain many pro tips for metal detecting.
You may find the answers to your questions by reading the FAQs here and from the related Knowledge Base Articles. Of course, if, after searching through this information you still have a question, there please contact our customer service team.
Yes, Minelab metal detectors have the ability to ‘discriminate’ between different types of targets. The discrimination feature on Minelab detectors measure two target properties, ferrous properties and conductive properties.
Ferrous properties refer to how much iron is in a target and therefore how strongly it’s attracted to a magnet. Ferrous targets tend to be trash, so can be discriminated/masked out based on their ferrous properties alone by the detector. Conductive properties refer to how well a target conducts electrical current and therefore responds to a metal detector’s magnetic field. Trash like nails and foil have different conductive properties to valuable targets like coins and rings. In this case the metal detector can make a judgement as to whether the target is trash based on conductivity.
The process for configuring the discrimination settings and the method used to indicate treasure or trash varies across the Minelab range of detectors.
As a rule of thumb, the lower the frequency used by the detector, the deeper it can penetrate the ground. At low frequencies however, sensitivity to small low conductive targets is reduced. The higher the frequency, the higher the sensitivity to small targets, but will not penetrate as deeply. In general, gold detectors operate at higher frequencies (to find small nuggets), while coin and treasure detectors work at lower frequencies for deeper penetration. The exception to this is MPS type metal detectors that are sensitive and deep seeking simultaneously.
Size
The size of a search coil can influence the detection depth or sensitivity of a metal detector. The larger the coil, the deeper it detects, but will have less sensitivity to small targets. Conversely the smaller the search coil’s diameter, the more sensitive it becomes but looses detection depth.
Smaller coils are lighter, easier to control and may be chosen for their ability to negotiate difficult terrain or undergrowth. They are also an advantage in areas of high trash.
Shape
The most common coil shapes are conventional solid round coils, elliptical shaped coils and the open web coils. The main reason for the change in shape is to conform to a physical requirement, i.e. an elliptical coil can be pushed around bushes or between rocks easier than a round coil and open web coils move through water easier and are lighter. Conventional round coils are often more stable and perform better and are particularly popular for gold prospecting.
Configuration
The three most common types of coil windings are Concentric, Double-D, and Monoloop. The difference between these coil types is the pattern the wire is wound within the search coil.
Concentric coil
A Concentric coil has an inner circle and an outer circle wire winding. Its search pattern is cone shaped and can be useful for accurately pinpointing a target. Concentric coils tend to be noisier in highly mineralised ground and require more over lap of sweep for thorough ground coverage.
Double-D coil
Double-D coils are the preferred coils for most detecting. They give a blade or chisel shaped signal that covers the ground more uniformly and once an operator becomes accustomed to the signal, pinpointing can be very accurate. Double-D coils are also preferred for their superior ground balancing ability.
Monoloop coil
Monoloop coils have one winding of wire around the circumference of the coil, which is used to both transmit and receive. The signal pattern of the Monoloop coil is cone shaped, requiring more overlapping. In extremely heavily mineralised grounds they can be more difficult to ground balance, however they tend to provide slightly better depth than the Double-D coils.
Dirt, dust and moisture can be trapped inside the skidplate leading to false signals and poor performance. To maintain peak performance of your Minelab detector, it is recommended to clean out the skidplate quite regularly.
코일 선택 가이드 를 확인하여 감지 요구에 가장 적합한 코일을 찾으십시오.
Headphone specifications are not really critical in a metal detector as their audio circuitry does not produce Hi-Fi quality sound. e.g. Our detectors frequency output range is only circa 75 -1200Hz
Our audio circuits will drive most headphones from 16 - 100 + ohms.
Audio optimisation is also very subjective as everybody hears differently.
We endeavour not to confuse our customers with unnecessary technical specs because in reality there is no honest way to determine what headphones are best for you other than to try them.
If you have a detector with adjustable audio tones, such as a CTX 3030, we would also recommend you spend some time to ensure the detection tones are optimised for your hearing needs.
There is no specific answer to this question as it depends on the target size, orientation, metallic content, ground minerals and conductivity, electrical and ambient noise in the area and etc.
However we commonly hear of GPX Series detectors finding large gold nuggets at 3 and sometimes 4 feet deep, and CTX 3030s finding coins and rings at over 12 inches.
Only if it becomes faulty.
On some detectors you don’t need to ground balance at all. On others, users new to detecting are recommended to use the Ground Balance Tracking function.
In Tracking, the detector will automatically ground balance for you and remain in balance even if the ground minerals vary. On manual ground balance detectors like the X-TERRA 305 and X-TERRA 505, you need to ground balance at the start of every hunt, and re-balance periodically as required. Always ground balance on clean ground, away from metal objects.
Gold chains are very difficult to detect, particularly very fine chains. Each link of a chain can be very small and the detector sees each link as a separate target, so it can easily be missed. You are more likely to detect the actual clasp or any pendants that may still be on the chain as these are much larger than the individual chain links. High frequency detectors such as the Eureka Gold, or an X-TERRA 705 with an 18.75 kHz coil in prospecting mode, will often pick up fine chains better than most coin detectors.
Coke is carbon and as such can be quite conductive, just like a coin.
The GPZ 7000 is our deepest detector in all ground conditions and can detect through even highly mineralised rock.
No, cable characteristics are matched to coil windings at manufacture, so extending the cable will reduce the performance of the coil.
Smaller coils are better for trashy sites, as they reduce the instances of detecting multiple targets at once. Concentric coils are generally better than Double-D coils for this same reason.
Check the coil selection guide to find the most suitable coil for your detecting needs.
Metal detectors pick up electromagnetic signals from underground metal objects. Similar signals can also be received through the air from other electromagnetic sources, such as power lines, radio transmitters, generators, etc.
If your detector is noisy when you are detecting, but goes quiet when you stop sweeping the coil, then it is receiving signals from mineralized ground. Perform a ground balance and continue detecting.
GPX series only: if it is still noisy then you may need to try an alternate soil/timing selection. All other detectors: if it is still noisy you would need to reduce your sensitivity to the highest stable sensitivity level.
The only guaranteed way to get every possible good target is to use no discrimination. However, digging every target can waste lots of time. Discrimination patterns are always a compromise between digging most good targets and ignoring most junk targets.
This can be caused by a number of reasons:
Usually because you are lifting the coil at the end of your swing. Always sweep slow, low and level for the entire swing.
Zero Voltage Transmission (ZVT) technology creates ultra‑constant high-power opposite polarity magnetic fields.
ZVT provides users with superior ground balance to enhance detector stability in mineralised soils and will detect gold nuggets at extreme depths that exceed all current competitor products.
The GPZ 7000 is our best performer on the medium to larger nuggets, even in highly mineralised or variable ground. It retains superior depth capabilities compared to any other detector while still providing good sensitivity to smaller, shallower targets.
The GPZ 7000 detector has Minelab branded, and aftermarket coils available for purchase. Minelab branded coils are available from Minelab certified dealerships. You can purchase the 14” or 19” Super-D coils.
NuggetFinder coil have released 2 Minelab approved aftermarket coils. A 12” round Super-D coil and a 17” elliptical Super-D coil which can be purchased by NuggetFinder stockists.
No, the GPZ 7000 does not have any discrimination capability.
The Difficult Ground Type setting is the default setting and is recommended as gold is usually found in areas with highly mineralised soils.
The Normal Ground Type setting will provide the greatest detection depth but can only be used in “quiet” soils where there are lower levels of mineralisation in the soil.
If the detector is running unstable or noisy when using a “Normal” ground type you should switch to “Difficult”.
The Severe Ground Type will provide the lowest detection depth and should only be used when detecting in areas with extremely high levels of mineralisation. This setting should only be used in areas where you need to raise the coil above the ground when using the “Difficult” Ground Type setting.
When ground balancing, the yellow ferrite ring artificially adds additional data to help the GPZ 7000 improve the ground balance accuracy. This should always be used to ensure smooth operation. Sweep the coil over the yellow ferrite ring in a figure 8 motion ground balancing, ensuring that you sweep over the yellow ferrite ring with each figure 8 movement.
When balanced correctly you should hear a smooth audio tone when sweeping the coil over the yellow ferrite ring.
When ground balancing the GPZ 7000 a swinging or figure-8 movement is recommended as the GPZ 7000 constantly monitors the changes in the soil. Sweeping the coil over as much ground as possible ensuring that you sweep over the yellow ferrite ring with each swing/figure-8 motion when ground balancing allows the detector to gain as much information as possible about the local ground conditions which provides a superior ground balance.
Wireless audio is susceptible to audio dropouts when the signal is blocked. Audio dropouts can be reduced by ensuring a direct line of sight between the WM12 and the detector. It is best to wear the WM12 as close as possible to the detector. This minimises the path to the wireless transmitter and makes it less likely that the operator's body will block the signal path between the WM12 and the detector.
The GPZ 7000 will operate for approximately 8 hours when commencing with a fully charged battery. Charging the battery will typically take 5 – 6 hours.
The WM12 wireless module will operate for approximately 12 hours on a fully charged battery and takes around 12 hours to charge when charging via the BC10 charger.
Yes, the GPZ 7000 can be charged from a nominal 24V battery system. The BC10 charger can will function between 11 – 30 volts DC.
You can also use the supplied 240V AC plug-pack if your vehicle is fitted with an inverter.
No, Minelab currently has no plans to release a replaceable cell or alkaline battery pack.
There are 2 USB cables supplied in the box with your GPZ 7000. The USB-A to Mini-USB cable is used for charging the WM12 wireless module.
The USB-A to USB-B is used for software updates and is plugged into the rear of the screen pod and a PC.
On the rear of the screen pod is a USB-B port that can be used if a software upgrade is released. Check the downloads section of the GPZ 7000 page on our website for updates.
GeoSense-PI™ 기술은 지상 신호를 매우 명확하고 정확하게 분석하고 응답하므로 한 번 감지할 수 없다고 생각했던 어려운 환경에서도 감지할 수 있습니다. 가장 작은 금 조각도 초고속으로 감지하기 위해 3개의 중첩 피드백 시스템을 통해 원치 않는 신호를 빠르게 억제합니다.
GPX 6000은 광물이 많이 함유된 땅이나 변하기 쉬운 땅에서도 더 많은 작은 너겟에서 최고의 성능을 발휘합니다. 더 크고 깊은 너겟에서 GPZ 7000 바로 뒤에서 뛰어난 깊이를 유지합니다.
GPX 6000 코일은 이전 GPX 시리즈 감지기와 호환되지 않는 새로운 범위의 경량 고성능 코일입니다.
GPX 6000의 14" Double-D 코일은 EMI 제거 또는 전도성 토양 신호 제거에만 사용할 수 있습니다. 철 식별이 불가능합니다.
The following Minelab coils are currently available to operate with the GPX 6000:
Minelab approved aftermarket coils are available from Coiltek and NuggetFinder.
코일에서 코일 케이블의 첫 번째 권선은 항상 샤프트 위로 가야 합니다. 그런 다음 코일 케이블을 샤프트 주위에 단단히 감고 두 개의 벨크로 스트랩으로 제자리에 고정해야 합니다. 감지 시 코일이 자유롭게 움직일 수 있도록 충분한 공간을 확보해야 합니다.
GPX 6000은 지면의 페라이트 성분을 추적하지 않습니다. GeoSense-PI는 다른 기술을 사용하여 운영자에게 보이지 않는 'X' 응답을 제거합니다.
GPX 6000의 접지 균형을 맞추기 위해 노란색 페라이트가 필요하지 않습니다.
임계값 톤은 Ground Type 버튼을 길게 눌러 모든 감도 설정에서 켜고 끌 수 있습니다.
임계값 톤은 수동 감도 범위에서 켜지고 자동 감도 범위에서 꺼집니다. 다음에 GPX 6000을 켜면 임계값 톤이 기본값으로 돌아갑니다.
어려운 지반 유형 설정은 특히 뜨거운 암석이나 매우 가변적인 지반과 함께 더 많이 광물화된 토양에서 가장 잘 사용됩니다.
일반 접지 유형 설정은 더 큰 너깃에서 가장 깊이가 있습니다. 가능한 한 항상 광물화 수준이 낮거나 가변성이 적은 지반에서 사용하는 것이 가장 좋습니다. 노멀 그라운드 타입은 뜨거운 암석을 타겟으로 잡을 수 있습니다. 뜨거운 암석이 균형을 이룰 수 없는 경우에는 어려운 접지 유형 설정을 사용해야 합니다.
The GPX 6000 with GeoSense-PI is continually tracking the ground, so either technique would work. Minelab recommends pumping the GPX 6000 up and down above the ground with the Quick-Trak button depressed to achieve the fastest Ground Balance.
전도성 접지는 눈에 보이는 소금과 연관될 필요가 없습니다. 예를 들어, 최근의 비는 토양을 더 전도성으로 만들고 원치 않는 전도성 토양 응답을 증가시킬 수 있습니다.
무선 오디오는 신호가 차단될 때 오디오 드롭아웃에 취약합니다. 오디오 드롭아웃은 헤드폰과 감지기 사이의 직접적인 가시선을 확보하여 줄일 수 있습니다. 블루투스 컨트롤이 감지기에 가장 가까운 헤드폰을 착용하는 것이 가장 좋습니다. 이렇게 하면 Bluetooth 송신기에 대한 경로가 최소화되고 작업자의 몸이 헤드폰과 감지기 사이의 신호 경로를 차단할 가능성이 줄어듭니다.
GPX 6000은 완전히 충전된 배터리를 시작할 때 약 8시간 동안 작동합니다. 배터리를 충전하는 데 일반적으로 5~6시간이 걸립니다.
ML 100 헤드폰은 완전히 충전된 배터리로 약 24시간 동안 작동하며 충전하는 데 약 3.5시간이 걸립니다.
GPX 6000 배터리는 차량에서 충전할 때 공칭 12V 차량용 배터리 시스템에서만 충전해야 합니다.
Minelab은 현재 교체 가능한 셀 또는 알카라인 배터리 팩을 출시할 계획이 없습니다.
USB 케이블은 Bluetooth 헤드폰을 충전하는 데 사용되며 GPX 6000에 대한 소프트웨어 업그레이드가 가능한 경우에 사용됩니다.
스피커 그릴 뒤에는 소프트웨어 업그레이드가 출시될 때 사용할 수 있는 USB 포트가 있습니다. 업데이트에 대해서는 당사 웹사이트 에서 GPX 6000 페이지 의 다운로드 섹션을 확인하십시오.
주어진 위치에 어떤 수준의 토양 광물화가 있을 것인지 예측할 수 없으므로 시작하는 것이 권장되는 시기는 보통입니다. 그런 다음 감지기가 코일을 스위핑하고 임계값의 안정성을 들어 어떤 타이밍을 사용할지 알려줄 수 있습니다.
Auto Tune 및 Ground Balance를 수행한 후에는 검색을 시작해야 합니다. 감지기가 너무 시끄럽거나 뜨거운 암석이 많은 신호를 보내는 경우 사용 중인 타이밍이 현재 있는 지면에 대해 너무 공격적입니다. 아래 스케일의 어두운 끝 부분에 더 가까운 다른 타이밍을 선택해야 합니다(예: Enhance).
GPX 5000은 특히 폭풍우가 치는 날씨에 전자기 간섭(EMI)을 겪는 것으로 알려져 있습니다. 이 간섭에 대한 세 가지 알려진 이유가 있습니다.
EMI가 좋지 않은 날에는 임계값을 푸르르게 유지할 수 있는 몇 가지 팁이 있습니다.
코일 Rx 스위치가 취소로 설정된 모노루프 코일을 사용하고 있지 않은지 확인하십시오.
Monoloop 코일은 완벽하게 둥근 케이블을 가지고 있습니다.
Double-D 코일은 2개의 내부 코어로 인해 케이블이 더 평평합니다.
코일/수신 스위치를 취소에 둡니다. 예상보다 깊이가 약간 줄어들었다면 코일은 Double-D입니다. 깊이가 거의 없다면 모노루프 코일이 있는 것입니다.
안정기 기능은 임계값의 미세한 변화가 들리기 시작하는 지점을 제어합니다. 이러한 희미한 변화는 주변 잡음 또는 희미한 목표 신호일 수 있습니다. 스태빌라이저 컨트롤을 높이면 희미한 타겟 신호가 더 커지지만 노이즈 레벨도 증가하여 원하는 타겟 신호를 잠재적으로 숨길 수 있습니다. 안정기를 사용하면 이러한 희미한 변화를 마스킹하여 완벽하게 안정적인 임계값을 제공하여 희미한 표적 신호를 식별하는 능력을 향상시킬 수 있습니다.
안정기는 해당 위치의 토양 조건이 결정될 때까지 FP(공장 사전 설정) 위치에 두는 것이 가장 좋습니다. 로컬 조건에 대해 Rx 게인 레벨이 설정되고 다른 오디오 설정이 선택되면 안정기를 사용하여 임계값 안정성을 미세 조정할 수 있습니다.
안정기의 최적 위치를 찾으려면 코일이 지면을 가로질러 스위핑되는지 확인하십시오. 임계값이 채터링을 시작하는 지점 아래의 한 숫자가 일반적으로 가장 좋은 설정입니다.
Stabilizer의 효과는 Rx Gain 컨트롤과 비슷한 효과를 낸다고 볼 수 있습니다. 그러나 Stabilizer는 오디오 처리에만 영향을 미치고 수신(Rx) 신호를 변경하지 않으므로 최종 단계의 미세 조정으로 사용해야 합니다. 스태빌라이저를 조정한 후 접지 조건이 변경되거나 코일을 변경하려는 경우 Rx 게인을 재설정해야 할 수 있지만 그렇게 하기 전에 먼저 스태빌라이저를 공장 사전 설정으로 되돌리십시오. 이렇게 하면 조건에 가장 적합한 Rx 게인 레벨을 선택한 다음 스태빌라이저를 사용하여 미세 조정할 수 있습니다.
팁: 스태빌라이저 컨트롤을 최소값(시계 반대 방향)에 가깝게 돌리면 임계값이 매우 안정적이지만 더 작은 대상에 대한 민감도를 많이 잃게 됩니다. 이것은 쓰레기가 많은 지역에서 큰 덩어리를 찾거나 GPX 5000 및 GPX 4800을 사용하여 동전이나 보물을 찾는 것과 같은 특정 시나리오에서 바람직한 기능일 수 있습니다.
팁: 이러한 컨트롤을 설정하는 가장 좋은 순서는 다음과 같습니다.
타겟 볼륨은 타겟 신호의 강도를 제어하며 8보다 높은 설정에서는 임계값의 볼륨도 약간 증가합니다. 이것은 바람이 많이 부는 조건, 청력 손실로 고통받는 사람들 또는 외부 스피커를 사용할 때 유용합니다. 리튬 이온 배터리 팩에 내장된 오디오 앰프를 사용하여 스피커를 배터리에 직접 연결하고 Target Volume을 사용하여 적절한 증폭 레벨을 설정할 수 있습니다. 헤드폰에서 외부 스피커로 전환할 때 임계값 및 볼륨 제한 컨트롤을 약간 조정해야 할 수 있습니다.
Target Volume은 조용한 조건에서 오디오 부스트로 사용할 수 있으며 광물질이 많이 함유된 토양에서 그라운드 노이즈 신호를 줄이거나 부드럽게 하는 데에도 사용할 수 있습니다. 이것은 강력한 기능이며 스태빌라이저 컨트롤과 함께 작동하여 궁극의 미세 조정 기능을 제공합니다. 다양한 조건에서 최적의 조합을 찾으려면 약간의 실험이 필요할 수 있습니다.
참고: 코일 또는 위치 변경으로 인해 게인 조정이 필요할 때마다 먼저 대상 볼륨이 FP 설정으로 돌아가도록 하십시오. 그런 다음 새 조건에 맞게 미세 조정할 수 있습니다.
The SDC 2300 is our compact and waterproof gold prospecting detector. It uses Multi Period Fast (MPF) Pulse Induction (PI) technology that provides excellent sensitivity when detecting small to medium sized nuggets in highly mineralised or variable ground. The SDC 2300 provides good depth on larger deeper nuggets.
No, there are no other Minelab branded coils available for the SDC 2300. The supplied 8” round coil provides excellent overall performance for the SDC 2300 and keeps the detector waterproof and compact
No, there is no discrimination function available for the SDC 2300.
Having no constant threshold audio emit through the speaker or headphones indicates that the threshold audio is in the OFF or minimum setting.
The threshold volume can be adjusted by pushing the threshold button on the right side of the handle.
There are 9 levels of Threshold audio which are indicated by the LED display. With each press of the threshold button, you will notice the LEDs on the display incrementally move to the right, the threshold audio will also start increasing. When the threshold level is at maximum, pressing the Threshold button will cycle the threshold level back to the OFF or minimum setting.
The SDC 2300 has 2 Audio pitch settings, Low or High. High pitch is the default, to change to the low setting switch the detector off then push and hold the Threshold button while switching the detector on.
The SDC 2300 will remember its previous setting so you will need to push and hold the Threshold button whilst switching the detector on to toggle back to the High pitch setting.
The SDC 2300 is waterproof to 3m (10ft) This is the complete detector including the control box.
Yes, the SDC 2300 has a salt mode in the sensitivity adjustment, however Minelab does not recommend using the SDC 2300 on the beach as the SDC 2300 does not have a discrimination or target ID feature so you will dig a lot of trash.
The salt mode in your SDC 2300 is designed to be used on conductive ground such as salt lakes or wet mineralised soils found in gold fields where a high salt content is apparent. For example, recent rains may make the soil more conductive and increase the unwanted conductive soil response. If the soil is conductive or you are detecting on a salt lake, then adjust the sensitivity dial to a salt setting.
To check the battery level on your SDC 2300 simply push and hold the Noise Cancel button then press and release the Threshold button. The Noise Cancel button can now be released.
An indication of the battery level will be displayed by the LED's for approximately 3 seconds.
The SDC 2300 will operate for approximately 8 hours when commencing with a fully charged Li-Ion battery. Charging the battery will typically take 5 – 6 hours. When using C-Cell Alkaline batteries you will generally have a longer use time (10-14 hours) but this will depend on the quality of the C-Cell batteries you are using.
No, The SDC 2300 battery should only be charged from a nominal 12V car battery system when charging from a vehicle.
The SDC 2300 includes a rechargeable Li-Ion battery pack inside the box. The battery compartment can also accept C-Cell Alkaline batteries or C-Cell NiMH rechargeable batteries. You can see the polarity for the C-Cell batteries on the side of the control box.
No, the software on the SDC 2300 cannot be upgraded.
The GOLD MONSTER 1000 is Minelab’s entry level gold prospecting detector, designed to find the smallest of nuggets in moderately mineralised ground. It retains excellent sensitivity to smaller shallow nuggets and can detect some larger nuggets at depth.
The Gold Chance Indicator at the top of the screen indicates if the target has a ferrous or non-ferrous content. If the indicator is consistently pointing to the right, it is indicating a high non-ferrous content and is likely a non-ferrous metal such as: gold, silver, brass, copper, aluminium, lead, zinc or other alloys that do not have any iron (ferrous) content.
If the indicator is pointing to the left, it is showing a high ferrous content and is likely steel or iron.
Large steel and iron (ferrous) targets can indicate on the right. This happens when the conductive properties of the large ferrous target dominate the signal and mask the magnetic properties of the target.
The GM05 and GM10 are the only compatible coils that can be used with the GOLD MONSTER 1000. The GM05 is included in the box and the GM10 coil can be purchased as an accessory from Minelab dealerships.
There are currently no aftermarket coils available for the GOLD MONSTER 1000.
The first winding of the coil cable from the coil should always go over the shaft. Winding the coil cable over the shaft provides minimal stress on the coil cable which will help avoid damage. The coil cable should then be wound closely around the shaft, allowing enough room for the coil to be able to move freely when detecting.
Press the coil cable into the clip on the rear of the screen pod and then carefully screw the coil connector into the rear of the screen pod.
There are 10 manual and 2 auto sensitivity levels.
Auto is located in position 11 on the sensitivity dial and will be indicated with a black dot in the centre of the sensitivity dial.
When in Auto the detector will function smoothly in most soil types and will continually adjust the detector’s sensitivity level to maintain smooth operation.
Auto + is located in position 12 on the sensitivity dial and will be indicated with a black dot in the centre of the sensitivity dial.
Auto + is a more aggressive sensitivity which provides users with additional sensitivity for extra depth performance. Auto+ should only be used in moderately mineralised soils as this setting may provide more ground noise.
Manual sensitivity adjustments (1 – 10) are for the expert user who has a good understanding of soil mineralisation and electro-magnetic interference (EMI).
Manual sensitivity allows the user to adjust the detector’s performance manually, when you have selected a sensitivity setting in the manual range the detector will not adjust levels like it does in the Auto or Auto+ modes. You may need to keep adjusting the manual sensitivity when in variable or heavily mineralised soil types.
The GOLD MONSTER 1000 is very sensitive, when you wave your hand over the coil the detector can detect the salt in your blood.
When you are retrieving a target, you should always use the supplied plastic scoop to ensure you detect the desired target and not your hand.
Because the GOLD MONSTER 1000 is highly sensitive to salt detection it is not recommended for beach use.
Chattering, or inconsistent audio is generally a sign that the detector is picking up interference from ground mineralisation or electro-magnetic interference (EMI). If you are in Auto +, try adjusting the sensitivity to Auto or a lower manual sensitivity. If lowering the sensitivity doesn’t fix the issue, then you should move away from sources of EMI. (power lines, cellular phone towers, power generators, thunder/electrical storms, etc.)
Random detection beeps can be caused by mineralisation in the soil. The GOLD MONSTER 1000 has an auto-tracking ground balance feature that continually monitors the minerals in the soil and adjusts the detectors’ ground balance. Rapid changes or high levels of mineralisation in the soil can cause the detector to false signal, if this happens, pump the coil up and down (0.5 - 10cm / 0.2 - 4”) over the areas that are giving false signals. This will help ground balance the detector to the mineralisation in the soil.
If the mineralisation level is too high, then lower the sensitivity to compensate for the mineralisation level.
Lifting your coil into the air will amplify any noise that is in the area. Minelab does not suggest doing this as this is not how our products are designed to be used. Lifting the coil slightly into the air is acceptable when performing a Noise Cancel, once the Noise Cancel is complete the coil should always be kept near the surface of the soil to avoid interference.
No, the GOLD MONSTER 1000 does not have any wireless capability. You can plug in any 3.5mm (1/8”) stereo headphones to the rear of the control pod.
The GOLD MONSTER 1000 will operate for approximately 12 hours when commencing with a fully charged Li-Ion battery. Charging the battery will typically take 5 to 6 hours.
No, the GOLD MONSTER 1000 battery should only be charged from a nominal 12V car battery system when charging from a vehicle.
No, the software in the GOLD MONSTER 1000 cannot be upgraded.
일부 컴퓨터의 바이러스 방지 소프트웨어는 Minelab 전자 메일을 스팸 파일 / 폴더에 저장합니다.이 전자 메일의 스팸 폴더를 확인하십시오. 이메일을받지 못한 경우 가까운 Minelab 공식 서비스 센터에 문의하십시오 .
When XChange 2 is first installed the 'file' icon will not appear until the software recognizes the CTX 3030 being connected for the first time. This is the only time this will happen. After the initial connection the 'FILE' icon will appear and remain. You will no longer need to connect the CTX 3030 to access it.
The factory setting for GeoTrails is off, so you will need to turn it on. First turn GPS ON, then turn GeoTrails ON. From the map screen, press and hold the Map button to access this option. Use the arrows to select ‘View GeoTrails’ and press the Select button.
Enhanced turns on SBAS or Satellite Based Augmentation System which is a generic term for WAAS used in the USA and EGNOS in Europe. These systems use a geostationary satellite to probe the atmosphere and TX this to your GPS receiver. It works well in the USA, but in Europe it seems to be better for planes rather than on the ground. In Australia you get signals from a satellite over Japan which makes your fix worse. Not sure how much of Europe has this as an issue.
The default for the 'User' button is to control the backlight, so if a user changes this to something else, then the backlight is controlled in the Menu/Options/Backlight - ON / OFF / TIME
You’re all done and your time zone has been set.
If you don’t know your UTC Time Zone please refer to the following link: http://www.timeanddate.com/time/map/
In a session, if the WM 10 Wireless Module is enabled and the detector is connected to it then you will hear tones as expected. If you turn off the WM 10 it will 'mute' the detector. Power cycle the detector and you will be able to hear the tones.
The CTX 3030 has a similar ground compensation feature to that on the Explorer SE Pro and E-TRAC models which works very well in most ground conditions, so there is no need to ground balance the CTX 3030 in most conditions. Ground balance should only be performed in 'Extremely Mineralised Ground'. Do not perform ground balance on the beach, this will 'confuse' the detector.
This is a standard feature, when you perform 'Tone ID profile edit', and select Play Tone or Play All, the tones will not sound if the WM 10 Wireless Module is connected.
There are 4 different volume settings. The CTX 3030 remembers what each setting is. If you turn the volume down while using the headphones and then unplug your headphones the external speaker volume will not have changed from your previous setting.
Before placing the twist-lock style armrest on the shaft, turn the lock fully counter clockwise. There is no need to turn the lock completely 90 degrees to lock it. Around 30 to 45 degrees is often sufficient.
This was corrected in a software update. Connect your detector to XChange 2 and check for software updates. We always recommend using the most current software update. If you're on the latest update or the update didn’t correct the problem please contact your regional Minelab Authorised Service Centre.
The modes will change (or be translated) ONLY when changing from ENGLISH to another language and not in reverse. If the detector is initially set up in a language other than English, the modes will appear in that language. But if you change the language to English later, the modes will stay in the original language.
The Trigger will Cancel any adjustment being made and go back one level in the menu.
If you’ve been using the detector a lot since the last time you connected it to XChange 2 then there is a lot of data stored. It could take several minutes for the data to upload. Please be patient.
This could be related to masking, low sensitivity setting, coil overload or etc. Perform a 'Factory Reset' and retest the detector.
To connect the WM 10 Wireless Module to your detector:
If Pairing fails, try selecting another channel
The location of the WM 10 can be an issue for path loss. The human body is very attenuating, so having the WM 10 tucked on your backside away from the detector could cause issues. If you’re having issues place the WM 10 in a clear line of sight to the detector to get best results.
Snapshots are only saved while the detector is on. It is a design feature that the snapshots are deleted when the detector is turned off.
During your initial use of GPS the detector will take a while to build up local data. From a cold start the 'locking in' of where satellites are and etc. takes a few minutes, but it can take an hour to build up lots of local data. This data can be used to get better resolution and shaded sky use.
This is as simple as saving the modes and/or data you want as a file and emailing them the file. Here’s the procedure:
All the modes and other data from your CTX 3030 will be displayed in the list.
The entire FILE Collection will be exported as a single file, and saved in the Downloads folder of your PC. You can then save the file elsewhere or email it to whoever you want.
If you receive a Minelab FILE from someone else simply open XChange 2, select the FILE Collection and then click the ‘Clear the contents of your File collection’ icon.
Then click the ‘Import a Minelab file’ icon.
Then click ‘Choose file’,
and browse for the file location. Highlight the file and click ‘Open’ and the Items within it will be displayed in the File Collection.
Drag and drop the items you want to keep into one of your own Collections or straight into your CTX 3030.
Combined audio produces different tones for highly ferrous objects, and objects with varying levels of conductivity. First you set the ferrous line (horizontal line) where you want ferrous targets to provide the audio response. For example, if you set it at 21, then any target with a ferrous reading of 21 or higher (larger number) will produce the audio tone that you program for ferrous targets. On the other hand, if the target has a ferrous reading that is less than 21, the audio response will be based on its conductive properties. In Combined audio you have four 'bins' representing conductive groups with conductive numbers running from 01 - 50. You simply move the lines to represent different target groups and assign a tone for each group. For example, you could set bin one with the lines at 01 and 14. Any target with a ferrous value less than 21, and a conductive value of 14 or less would fall into this bin and provide the audio tone you associated with it via programming.
Bin two, for example, could represent targets between 15 and 28. Bin three could represent targets from 29 - 40 and bin four could be the remainder of conductive targets with CO values of 41 - 50. With the numbers used in these examples, if you passed over a target with a FE value of 12 and a CO value of 44, it would provide the conductive tone you assigned to conductive bin four. If you passed over a target with an ID of 11 – 22, it would provide the tone assigned to conductive bin two. Again, the user can resize and assign tones to each target group (bin). For those of you who enjoyed hunting in Two Tone Ferrous with the E-TRAC, this takes it one step further allowing you to adjust the FE line, and break down the CO targets into four separate groups.
Gold can ID anywhere in the range of 10-09 to 13-30, and possibly outside of this range. Sometimes the Conductive reading can be very low, like 02, so to improve your chances you really have to dig everything including aluminium foil and pull-tabs.
Regarding settings, the standard Beach mode is quite suitable. One thing you can do is to change the Tone ID profile to Ferrous 35. What this does is it will make low conductive jewellery produce a higher tone than it would in Conductive profile, making it easier to recognize. You can also select Combine, and customize the tones to suit your personal preference.
For saltwater beaches, Manual Sensitivity is recommended, unless your beaches have high levels of magnetic mineralization. If your unit is running nice and stable on Sensitivity 18, try to push it a bit higher. In situations where you are actually detecting in the salt water, turn the Seawater setting on.
The other thing some beach combers often do is to open up the discrimination pattern a little. Mainly dropping the ferrous rejection slightly or simply search in Pattern 2 (simply press and release the Detect button). This is highly recommended on beaches with low levels of junk targets. In this case another thing you can try is changing the Audio Response to LONG. This can improve your ability to hear the very faint target response which jewellery can produce.
Watch the approved Community Instructional Video on Editing FindPoints and WayPoints.
Watch the approved Community Instructional Video on How to link photos from your phone to FindPoints.
Watch the approved Community Instructional Video that includes How to record a GeoHunt.
Watch the approved Community Instructional Video that includes How to record a FindPoint or WayPoint.
Watch the approved Community Instructional Video that includes How to enable the GPS function.
Watch the approved Community Instructional Video that includes Turning on Detect screen options.
Watch the approved Community Instructional Video that includes Turning on the large target ID panel.
Watch the approved Community Instructional Video that includes Turning on the Sensitivity panel.
Watch the approved Community Instructional Video that includes Turning on the detect screen navigation tool.
Watch the approved Community Instructional Video that includes Selecting a Search Mode on the CTX 3030.
Watch the approved Community Instructional Video that includes Editing a Search Mode on the CTX 3030.
Watch the approved Community Instructional Video that includes transferring data from a CTX 3030 to XChange 2.
Watch the approved Community Instructional Video that includes Creating a new Collection on XChange 2.
Watch the approved Community Instructional Video that includes Changing XChange 2 preferences.
Watch the approved Community Instructional Video that includes Adjusting Universal settings.
Watch the approved Community Instructional Video that includes Making a new Search Mode in XChange 2.
No, The FBS 2 coils can only be used on the CTX 3030, while FBS coils can only be used on the E-TRAC, Safari and Explorer Series detectors.
MULTI-IQ+ is the next generation of MULTI-IQ technology and provides more power with lower electromagnetic interference (EMI) in built up areas.
This provides superior performance and depth allowing users to find previously undetectable targets in most locations.
MANTICORE에 사용된 MULTI-IQ+ 기술은 더 나은 감지 깊이, 향상된 복구 속도, 더 많은 감도 조정 및 사용자에게 더 많은 정보를 제공하는 고급 2D 식별 화면과 동일한 더 많은 전력과 더 빠른 처리를 제공하므로 MANTICORE는 거의 모든 면에서 EQUINOX 감지기를 능가합니다. 땅을 파기 전에 목표물을 찾아보세요.
현재 MANTICORE와 호환되는 다른 코일은 없습니다.
액세서리 코일은 현지 Minelab 대리점에서 구입할 수 있습니다. 가장 가까운 대리점을 찾으려면 온라인 대리점 찾기 도구를 사용하십시오.
ML105 헤드폰은 MANTICORE 감지기와 함께 상자에 포함되어 있으며 폼 패드가 머리 위에 위치하여 귀를 감싸는 오버이어형 헤드폰입니다.
ML85 헤드폰은 폼 패드가 귀 바깥쪽에 위치하는 온이어형 헤드폰입니다.
ALL TERRAIN GENERAL: 대부분의 대상과 조건에 대해 탁월한 만능 성능을 제공합니다. 뛰어난 타겟 분리 및 뛰어난 쓰레기 거부 기능을 제공합니다.
ALL TERRAIN FAST: 회수 속도가 향상되어 탁월한 표적 분리 및 우수한 코크스 제거 기능을 제공합니다.
모든 지형 고전도체: 은화 스택 또는 구리 타겟과 같은 고전도체에 탁월하며 우수한 타겟 ID 분리를 제공합니다.
모든 지형 낮은 도체: 망치로 두드린 동전이나 순금 장신구와 같은 작고 얇은 물체에 탁월합니다.
모든 지형 쓰레기 거부: 쓰레기가 많은 지역에서 사용됩니다. 최대 철 거부율
해변 일반: 건조하거나 젖은 모래 위에서 사용할 때 대부분의 대상과 해변 조건에 대해 탁월한 만능 성능을 발휘합니다. 뛰어난 타겟 분리 및 뛰어난 쓰레기 거부 기능을 제공합니다.
BEACH LOW CONDUCTORS: 금 사슬과 같은 작거나 얇은 대상에 탁월합니다. 건조하고 젖은 모래 모두에 적합합니다.
BEACH DEEP: 금 사슬과 같은 작거나 얇은 대상에 탁월한 깊이를 제공하는 낮은 복구 속도입니다. 건조하고 젖은 모래 모두에 적합합니다.
해변 서핑 및 해수: 수중 또는 서핑 감지를 포함한 까다로운 바닷물 조건에 탁월합니다.
GOLDFIELD 일반: 양성에서 중간 정도의 광물 토양에 있는 작은 덩어리에 탁월합니다. 이 모드는 금 덩어리에 대해 전반적으로 더 나은 성능을 제공하며 사용자가 희미한 표적 반응을 들을 수 있도록 돕는 연속 피치 오디오를 포함합니다. 이 모드는 쓰레기가 많은 영역에는 권장되지 않습니다.
빈도가 MULTI-IQ+로 설정된 경우 철류 타겟에는 비철류 타겟과 동일한 눈금의 타겟 ID가 할당되며 이는 비철류 타겟 ID와 동일한 눈금으로 표시됩니다. 내부 프로세서가 타겟을 철금속으로 분류하면 탐지기는 타겟 ID 번호 아래에 빨간색 철 표시기와 함께 낮은 오디오 신호음을 내며 2D 화면에서는 타겟이 타겟에서 멀리 떨어진 화면 상단이나 하단에 표시됨을 나타냅니다. 중앙 전도성 라인. 
*이미지는 설명 목적으로만 사용됩니다.*
일부 동전과 유사한 철 및 전도성 특성이 결합된 복잡한 철 타겟은 일반적으로 2D 화면의 아래쪽 절반에 나타납니다.
더 큰 철 타겟이 화면 상단에 나타납니다. 
전도성이 높은 대형 볼트와 같은 원통형 모양의 대형 철 타겟도 있을 수 있습니다. 이러한 유형의 타겟은 철 및 비철 영역 모두에서 타겟 추적을 표시할 수 있습니다.
*이미지는 설명 목적으로만 사용됩니다.*
차별을 통해 사용자는 개인 또는 대상 ID 그룹을 수락하거나 거부할 수 있습니다. 식별이 조정되면 철 및 비철 타겟 ID 모두에 변경 사항이 적용됩니다. 이는 선택한 타겟 ID의 철 및 비철 부분을 모두 회색으로 표시하는 수직선으로 표시됩니다.
철류 한계를 통해 사용자는 감지기 매개변수를 조정하여 무엇이 철류 또는 비철류 타겟으로 감지되는지 결정할 수 있습니다. 이는 2D 화면의 상단과 하단 모두에서 조정할 수 있습니다.
*이미지는 설명 목적으로만 사용됩니다.*
일반적으로 검출기를 사용할 경우 다중 주파수가 단일 주파수보다 우수합니다. 그러나 특정 주파수가 고유한 이점을 갖는 특수한 상황이 있을 수 있습니다.
*단일 주파수를 사용하는 경우 철류 한계가 비활성화되고 철류 타겟은 1~19의 타겟 ID를 제공하고 화면에 빨간색 철류 표시를 표시합니다.*
일반적인 사용 시간은 완전 충전 후 약 10시간 입니다 . MANTICORE 감지기는 0.5A 또는 2A(@ 5V) 출력 기능을 지원하는 모든 USB 보조베터리에서 직접 전원을 공급받을 수도 있습니다. 이는 사용되는 보조 배터리에 의해서만 제한되는 지속적인 런타임을 효과적으로 제공합니다.
*MANTICORE 감지기가 USB 보조 배터리에 연결된 경우 수중에서는 사용할 수 없습니다*
MANTICORE 감지기는 USB 2.0 표준을 준수하는 장치에서의 충전을 지원합니다. QuickCharge™는 더 높은 전압을 사용하고 MANTICORE 감지기와 호환되지 않는 Qualcomm에서 개발한 독점 표준입니다 .
완전히 방전된 상태에서 100%까지 충전 시간은 고용량 충전기(>1.7A @ 5V)로 충전 시 약 7시간 입니다.
USB 배터리 충전 1.2(BC1.2)와 호환되는 모든 표준 USB 포트를 사용하여 배터리를 충전할 수 있지만 저전력 옵션을 사용하는 경우 충전 시간이 더 길어질 수 있습니다.
모든 배터리의 수명은 사용자가 어느 정도 제어할 수 있는 여러 요인에 따라 달라집니다. 온도, 보관 시 충전 수준, 충전 주기 등 리튬 이온 배터리의 수명이 단축되는 가장 일반적인 원인은 완전히 충전된 배터리를 높은 온도에서 유지하는 것입니다.
감지기에 사용되는 모든 구성 요소와 마찬가지로 당사는 책임 있는 공급업체로부터 최신 고품질 구성 요소만을 엄격하게 조달합니다. 수년 동안 사용자가 배터리 문제를 겪을 것으로 예상하지 않습니다. Li-ION 배터리를 사용하는 CTX 3030 및 GPZ 7000 감지기에 대한 우리의 경험에 따르면 대다수의 사용자는 교체 배터리를 구입할 필요가 전혀 없었습니다.
아래에 설명된 대로 MANTICORE 배터리를 충전할 때는 평판이 좋고 인증된 USB 충전기만 사용하십시오.
핸들에 포함된 리튬 이온 배터리는 교체가 가능하며 보증 기간이 적용됩니다. 구입일로부터 6개월. Minelab에서는 방수 씰의 손상 가능성과 감지기 보증 무효화를 방지하기 위해 공인 서비스 센터를 이용할 것을 권장합니다.
네, 육지에서 감지할 때는 제한이 없습니다. 그러나 감지기를 충전 중이거나 보조 배터리에 연결한 상태에서는 수중에서 사용해서는 안 됩니다.
예. 감지기를 사용하는 경우 USB 보조 배터리로 전원을 공급할 때 보조 배터리에 여유 용량이 충분하면 배터리 충전 속도가 느려질 수 있습니다.
예. 물이나 해변에서 감지한 후에는 깨끗하고 담수로 감지기를 세척하는 것이 좋습니다. 감지기를 청소할 때 연마제나 용제를 사용하지 마십시오.
아니요. 방수 씰을 포함하여 감지기의 어떤 부분에도 윤활유를 칠할 필요가 없습니다. 석유계 그리스를 사용하면 방수 씰이 손상되고 보증이 무효화됩니다.
물속이 깊거나 물에 완전히 잠긴 경우에는 Minelab 방수 헤드폰 만 사용하는 것이 좋습니다. 여기에는 MANTICORE와 함께 사용할 때 방수 밀봉을 형성하도록 특별히 설계된 커넥터가 있습니다. 이 헤드폰은 현지 Minelab 대리점에서 구매 가능한 액세서리로 제공됩니다.
Hardwired coils are more reliable for deep diving detectors.
No, 8 x 1.2V is only 9.6V, and these detectors require 12V to function.
Check to ensure the battery is fully charged. A low battery causes the threshold to get very loud and the response becomes erratic.
Salt, sand and grit will accumulate on the Excalibur II. So make sure you thoroughly rinse it with fresh water after use, including the coil cover, shafts and battery pack. Don't forget the vent holes on each headphone diaphragm as these need to be clear if used for diving purposes to allow for ear equalisation.
The Multi-IQ engine in all EQUINOX series is the same, there are however processor enhancements in the EQUINOX 700 and EQUINOX 900 that allow the detector to provide users with better Iron Bias, target separation and discrimination depth.
Park 1 (General/Coins)
Park 1 is optimised for modern coins and larger jewellery with a default discrimination pattern set to reject many common aluminium foil-like targets. Therefore, this is the ideal Profile to start with to learn EQUINOX before experimenting with the other Modes and more specialist settings. Park 1 Multi-IQ processes a lower frequency weighting of the multi-frequency signal, as well as using algorithms that maximise ground balancing for soil to achieve the best signal-to-noise ratio. Hence Park 1 is most suited for general detecting and coin hunting.
Park 2 (Fine jewellery)
Park 2 is ideal for smaller targets in trash-infested (including ferrous trash) locations. It will detect a wider range of targets including low conductor (or higher frequency) targets, e.g. fine jewellery. All non-ferrous targets are accepted by default. Recovery Speed is increased to clearly identify good targets masked by iron trash. Target Tone is set to maximum to provide as much target information as possible via audio. Park 2 Multi-IQ processes a higher frequency weighted multi-frequency signal while ground balancing for soil.
Field 1 (Coins and Artefacts)
Field 1 is for general hunting with high trash rejection. This assists in locating desired targets more easily. The default discrimination pattern is set to reject most coke signals. The first Tone Break is set so that the coke signals will produce the same low tone as ferrous targets. Field 1 Multi-IQ processes a lower frequency weighted multi-frequency signal, as well as using algorithms that maximise ground balancing for soil, to achieve the best signal to noise ratio. Hence being most suited for general detecting and coin hunting.
Field 2 (Fine coins and Artefacts)
Field 2 suits locations with high target and trash densities. It will better detect small hammered coins on their edge or at greater depth. The default discrimination pattern is set to reject most coke signals. Target Tone is set to maximum to enhance audio identification and Recovery Speed is faster. The first Tone Break has been set so that the coke signals will produce the same low tone as ferrous targets. Field 2 Multi-IQ processes a higher frequency weighted multi-frequency signal while ground balancing for soil.
Beach 1
Beach 1 is most useful for detecting in wet or dry beach sand and also in shallow water where conductive salt signals are prevalent. It has good sensitivity to coins and small/large jewellery. Beach 1 reduces the salt signal, while maintaining high transmit power, and still being sensitive to desirable targets. Beach 1 Multi-IQ processes a low frequency weighted multi-frequency signal, and uses special algorithms to maximise ground balancing for salt
Beach 2
Beach 2 gives the best results when either wading or shallow diving with the coil and/or detector fully submerged. In these instances, there is a very strong salt signal present, so Beach 2 has a lower transmit power, which results in much less noise. This profile may also be useful in dry conditions where there are extremely high ground noise levels. Beach 2 Multi-IQ processes a very low weighted multi-frequency combination, using the same algorithms as Beach 1 to maximise ground balancing for salt.
Multi-IQ (EQUINOX 800 & 900 only)
Gold 1
Gold 1 is suitable for searching for small gold nuggets in ‘mild’ ground. Most goldfield locations have a variable level of iron mineralisation that will require an ongoing Ground Balance adjustment, therefore Tracking Ground Balance is the default setting. The audio Threshold Level and Threshold Pitch are optimised for hunting for gold nuggets. Gold 1 Multi-IQ processes a high frequency weighted multi-frequency signal, while ground balancing for mineralised soil.
Gold 2
Gold 2 is best for searching for deeper gold nuggets in ‘difficult’ ground conditions. Gold 2 has a lower Recovery Speed, which will increase detection depth. However, more ground noise in more heavily mineralised grounds may result. Tracking Ground Balance is the default setting. The audio Threshold Level and Threshold Pitch are optimised for hunting for gold nuggets. Gold 2 Multi-IQ processes a high frequency weighted multifrequency signal, while ground balancing for mineralised soil.
EQUINOX 700
• Weight has been decreased to 1.27kg (2.8lb)
• Waterproof to 5m (IP68)
• Three piece collapsible shaft now 144cm - 61cm (56.7" - 24")
• All carbon fibre shafts
• New, easily adjustable armrest
• 119 Target ID Range (-19 to 99)
• 119 discrimination notch segments
• "Depth Pitch" audio option in all modes
• Improved target separation
• Improved ferrous rejection
• Red LCD backlight
• Keypad backlight
• LED flashlight
• Handle vibration target indication
EQUINOX 900
• All above features
• Greater Sensitivity range 1 - 28
• Includes EQX06 6" waterproof DD coil
The new carbon fiber shaft design allows users to pack the detector down to 61cm (24 in) and has a full extension of 144cm (56.7 in)
Depth performance will differ depending on conditions and detector settings. Beach performance is better overall. Enhancements have been made to improve recovery speed, target separation and discrimination depth allowing users to have solid target IDs at better depths. EQUINOX 900 comes with 28 levels of sensitivity allowing more depth where environmental conditions allow the sensitivity to be turned up.
What are the frequency differences between the EQUINOX 600, 700, 800 & 900?
The EQUINOX 600 and 700 offer a choice of 4 single selectable frequencies:
• 4kHz
• 5 kHz
• 10 kHz
• 15 kHz
The EQUINOX 800 and 900 offers the choice of 6 single selectable frequencies:
• 4kHz
• 5 kHz
• 10 kHz
• 15 kHz
• 20 kHz
• 40 kHz
Gold Mode is designed to enhance performance on small gold nuggets in mineralized ground. It does so primarily by using different audio processing so that targets respond both in volume and pitch. The Gold Mode will be of interest to gold prospectors but has less application for other uses.
While the EQUINOX 600 and 700 do not have a dedicated Gold prospecting mode. Multi-IQ is so good in both Park 2 and Field 2, that these profiles are as good, or better, at finding gold nuggets than many dedicated single-frequency gold detectors. Multi-IQ provides very stable ID’s which is great for choosing what targets to dig in a goldfield.
Iron Bias is a setting that lets you choose how you want iron in the ground to sound. If you have a low setting, more of the iron will come through as a good target to dig up. This will also give you the best chance of finding any valuable non-ferrous targets nestled among the iron.
However, if you desire to hear less false audio sounds from the iron in the ground, try increasing the Iron Bias setting.
The Iron Bias in the EQUINOX 700 and EQUINOX 900 has had some changes to improve discrimination depth.
EQUINOX 600 and 800 have the option to choose either FE Iron Bias or F2 Iron Bias. FE Iron Bias will provide control over the target ID response. F2 Iron Bias will provide tone and target ID response adjustment for a wider range of ferrous targets.
Iron Bias in the EQUINOX 700 and EQUINOX 900 is based off the F2 Iron Bias in the EQUINOX 600 and EQUINOX 800 but allows even better overall depth detection and target separation. Because of this there is no F2 option available in the EQUINOX 700 or EQUINOX 900.
Yes, Coiltek Coils manufacture Minelab approved aftermarket coils for the EQUINOX and X-TERRA-PRO detectors.
No, they have different technology requirements and are not compatible. Only Minelab EQX coils are compatible with EQUINOX series detectors.
Having a larger target ID scale allows the detector to provide the user with more information on the target prior to digging it. This allows users to identify more targets individually which will help determine if the target is valuable or trash.
In general, Multi is superior to the single frequencies when using an EQUINOX. However, there may be specialised situations where a particular frequency has a unique advantage. The EQUINOX Series offers users simultaneous Multi-Frequency plus a wide range of single selectable frequencies for specialist situations.
Yes, there is no need to perform a full factory reset. Individual Search Profiles can easily be returned to their factory preset settings. Only the local settings will be reset and any global settings will remain in their last-use state.
Beach Mode automatically senses black sand and reduces the transmit power to ensure that targets can still be detected without overloading occurring. When black sand is sensed, the Beach Overload Indicator will appear on the LCD. When this icon disappears, full transmit power automatically resumes.
Depth Pitch is an audio mode that provides a continuous pitch audio with no threshold tone. It provides separate audio for ferrous and non-ferrous targets with a variable pitch.
Small or deep targets providing a weaker signal will have a lower pitch.
Large or shallow targets providing a stronger signal will have a higher pitch.
EQUINOX 700 and EQUINOX 900 have been designed to handle harsh outdoor environments. Our testing includes drop tests up to 1m, flex and water ingress testing. Both models are IP68 rated and can be submerged up to 5m (16ft)
Middle and Lower shafts can be mixed. They are not identical in size so they may not provide an exact fit. Upper shafts cannot be changed as the physical mounting point of the control pod is different.
Yes. The supplied magnetic USB charge cable can be used on all EQUINOX models, MANTICORE and X-TERRA PRO detectors.
The charge time, from completely flat to 100%, is approximately 4 hours when charged with a high capacity charger (>1.7A @ 5V).
Longevity for all batteries depends on a number of factors that are often controllable to some degree by the user; such as temperature, charge levels when stored, charge cycles etc. The most common cause of reduced life of Li-ION batteries is keeping a fully charged battery at elevated temperatures.
As with all components used in our detectors, we stringently source only modern high quality components from responsible vendors. We do not expect users to experience any battery issues over years of use. Our experience with the CTX 3030 and GPZ 7000 detectors which both use Li-ION batteries is that the vast majority of users have never needed to purchase a replacement battery.
• Avoid charging or using in extreme temperatures.
• Avoid rapid extreme temperature swings.
• Use only Minelab or Minelab recommended USB chargers and avoid so-called ultrafast chargers from third-parties that claim to fully charge Li-ION batteries in less than one hour.
• Before storing the detector for prolonged periods, the battery should be charged to approximately 50-60%. On the EQUINOX Battery Status Indicator, 2-bars is the optimum charge for prolonged storage. Maintaining the 2-bar charge periodically during extended storage is also advisable. Extended storage in temperatures less than 30oC (86’F) will also minimize degradation to Li-ION battery life
Use only reputable and certified USB Chargers when charging the EQUINOX battery as detailed below:
Typical runtime, from a full charge using wired headphones, is approximately 12 hours. The EQUINOX Series detectors can also be powered directly from any USB Power Bank that supports 0.5A or 2A (@ 5V) output capability. This effectively gives a continuous runtime only limited by the power banks being used.
The EQUINOX detectors support charging from devices that comply to the USB 2.0 standard. QuickCharge™ is a proprietary standard develop by Qualcomm that uses a higher voltage and is not compatible with EQUINOX detectors.
손잡이에 포함된 리튬 이온 배터리는 교체가 가능하며 구입일로부터 6개월 동안 보증이 적용됩니다. Minelab에서는 방수 씰의 손상 가능성과 감지기 보증 무효화를 방지하기 위해 공인 서비스 센터를 이용할 것을 권장합니다.
*EQUINOX 600 및 EQUINOX 800 배터리는 EQUINOX 700 또는 EQUINOX 900과 호환되지 않습니다.
Yes, when detecting on land, without any limitations. However, the detector must not be used underwater whilst charging or when connected to a power bank.
Yes. If the detector is being used, when powered by a USB power bank, the battery may charge at a slower rate if there is enough spare capacity in the power bank.
Yes. Connecting the WM 08 to a power bank will allow you to continue to use it even if the battery is low/flat. The power bank will charge the WM 08, which will continue operating as normal.
*Please note that the WM08 is not compatible with the EQUINOX 700 OR EQUINOX 900
No. They are separate wireless technologies and only one can be used at any one time.
*Please note that the WM08 and Bluetooth headphones are not compatible with the EQUINOX 700 OR EQUINOX 900
Re-pairing will be required if a different wireless device has been connected to the Equinox 600 or Equinox 800 (e.g. WM 08), or following a detector factory reset.
AUDIO
Bluetooth® Hearing Aids are largely intended to allow the wearer to intentionally connect to other Bluetooth® compatible devices, such as phones and audio streams. They enable the wearer to stream audio on-the-go without having to remove the hearing aid and insert earbuds.
The EQUINOX 600 and EQUINOX 800 detectors are Bluetooth® compatible devices.
While there are various different types of streaming audio hearing aids available on the market, if the hearing aid supports Bluetooth® A2DP or Bluetooth® aptX-Low Latency™ then it will be compatible with the EQUINOX 600 and EQUINOX 800 detectors.
Pairing with the EQUINOX 600 or EQUINOX 800 is achieved by pressing and holding the Wireless button on the side of the Control Unit for 5 seconds.
While pairing is being performed the Wireless icon on the LCD will flash rapidly for 15 seconds. After 15 seconds the Bluetooth® icon will start flashing on the LCD to indicate a Bluetooth device is being paired.
The initial pairing may take up to 5 minutes. During the pairing process the user should not press the Wireless button as this will stop the pairing process.
Once paired, the EQUINOX 600 or EQUINOX 800 will display a solid Bluetooth® icon on the top right of the LCD. If the hearing aid is aptX-Low Latency™ Bluetooth compatible the ‘+’ icon will also be displayed.
Consult your Hearing Aid User Manual for additional pairing instructions specific to your hearing aid.
*Please note that EQUINOX 700 and EQUINOX 900 are not currently compatible with hearing aids.
Yes, the Equinox 600 can still pair to Bluetooth A2DP or Bluetooth aptX-Low Latency headphones.
Yes. It is good practice to wash the detector with clean fresh water after detecting in water or on the beach. Never use abrasives or solvents to clean the detector.
Whenever washing or using your detector underwater always ensure that the plastic bung on the rear of the control pod is firmly screwed into the headphone jack.
No. It is not necessary to lubricate or grease any part of the detector, including the waterproof seals. Using any petroleum-based grease will damage the waterproof seals and void the warranty.
If deep wading or fully submerged, we recommend using only Minelab Waterproof EQUINOX Headphones. These have a specially engineered connector that forms a waterproof seal when used with the EQUINOX. These headphones are available as an accessory from your local Minelab authorised dealership (Part Number: 3011-0372)
Yes, the MULTI-IQ technology in the X-TERRA ELITE is the same as the MULTI-IQ technology used in other MINELAB metal detectors.
X-TERRA ELITE includes a 15kHz single frequency option for the Park and Field modes.
X-TERRA ELITE는 우수한 성능을 갖춘 합리적인 가격의 감지기를 찾는 보다 헌신적인 감지기를 위해 설계되었습니다. 사용자는 탐지기가 탐지 성능을 조정할 수 있도록 더 많은 제어 및 설정 조정 기능을 제공합니다. X-TERRA ELITE는 5미터(15피트)까지 방수가 가능하며 현재 시중에 나와 있는 다른 단일 주파수 감지기와 비교할 때 탁월한 성능을 제공합니다.
VANQUISH 시리즈는 탁월한 성능을 제공하면서도 최소한의 설정 조정으로 사용이 매우 용이하도록 설계된 스위치 온 앤 고(Switch-On) 유형의 감지기입니다. 이는 MULTI-IQ 프로세서가 모든 어려운 작업을 수행하므로 가능합니다.
VANQUISH 감지기는 초보자에게 권장되며, X-TERRA ELITE 감지기는 초급 감지기에서 업그레이드하려는 중급 감지기 사용자에게 권장됩니다.
V*X 또는 EQUINOX 시리즈 코일은 X-TERRA ELITE와 함께 사용할 수 있지만 이전 X-TERRA 305, 505 및 705 시리즈 코일을 포함하여 다른 Minelab 브랜드 코일은 사용할 수 없습니다.
X-TERRA ELITE에는 V12X 12인치 Elliptical Double-D 코일이 상자에 함께 제공됩니다. 현지 Minelab 대리점에서 아래 액세서리 코일을 구입할 수 있습니다.
X-TERRA ELITE will out-perform the VANQUISH and X-TERRA PRO detectors in all terrains on most targets. Performance may be similar in some circumstances but will differ depending on ground mineralisation levels but more specifically the type of metal each target consists of.
The X-TERRA ELITE provides unprecedented performance in salty conditions. There are 2 beach modes to ensure stability in both wet and dry salty environments.
Yes, you can purchase the Minelab WM09 wireless module, ML85 headphones or ML105 headphones as all of these are compatible with the X-TERRA ELITE. (note that the X-TERRA ELITE EXPEDITION model includes the ML85 headphones in the box)
X-TERRA ELITE는 현재 버전의 BLUETOOTH와 호환되지 않는 독점 무선 오디오를 사용합니다. Minelab ML85 또는 ML105 헤드폰과 WM09 무선 모듈은 X-TERRA ELITE와 호환되며 현지 공인 Minelab 대리점에서 구입할 수 있습니다.
Park 1 provides a default MULTI-IQ transmit frequency and is optimised for detecting modern coins and larger jewellery. This is a good mode to learn the X-TERRA ELITE before experimenting with other settings.
Park 2 provides a default MULTI-IQ transmit frequency and is optimised for detecting fine jewellery and smaller targets in trash infested areas. Recovery speed in Park 2 is increased to clearly identify good targets masked by iron trash.
Field 1 provides a default MULTI-IQ transmit frequency and is optimised for detecting modern coins and general detecting. It has a high trash rejection which makes it an ideal detect mode for areas containing coke.
Field 2 provides a default MULTI-IQ transmit frequency and is optimised for locations with high target and trash densities. This mode is great for coins on edge or sitting at greater depths. It has a high trash rejection which makes it an ideal detect mode for areas containing coke.
Beach 1 provides a default MULTI-IQ transmit frequency and is optimised for dry and wet sand. Beach 1 mode has a lower recovery speed for better depth across all targets and is good for detecting coins and small to large jewellery.
Beach 2 provides a default MULTI-IQ transmit frequency and is optimised for underwater usage where a very strong salt signal is present. To compensate for the high salt content Beach 2 has a lower transmit power. Beach 2 can also be used in dry soils that have a high salt content.
Yes, there is no need to perform a full factory reset. Individual Search Profiles can easily be returned to their factory preset settings. Only the local settings will be reset and any global settings will remain in their last-use state.
Typical runtime, from a full charge using wired headphones, is approximately 12 hours. The X-TERRA ELITE detector can also be powered directly from any USB Power Bank that supports 0.5A or 2A (@ 5V) output capability. This effectively gives a continuous runtime only limited by the capacity of the power bank.
The X-TERRA ELITE detector supports charging from devices that comply to the USB 2.0 standard. QuickCharge™ is a proprietary standard develop by Qualcomm that uses a higher voltage and is not compatible with X-TERRA ELITE detectors.
The charge time, from completely flat to 100%, is approximately 4 hours when charged with a high capacity charger (>1.7A @ 5V).
Longevity for all batteries depends on a number of factors that are often controllable to some degree by the user; such as temperature, charge levels when stored, charge cycles etc. The most common cause of reduced life of Li-ION batteries is keeping a fully charged battery at elevated temperatures.
As with all components used in our detectors, we stringently source only modern high quality components from responsible vendors. We do not expect users to experience any battery issues over years of use. Our experience with the CTX 3030 and GPZ 7000 detectors which both use Li-ION batteries is that the vast majority of users have never needed to purchase a replacement battery.
Use only reputable and certified USB Chargers when charging the X-TERRA ELITE battery as detailed below:
The Li-ION battery contained in the handle is replaceable and covered under warranty for a period of 6 months from the date of purchase. Minelab recommends using an Authorised Service Centre to avoid potentially damaging the waterproof seal and voiding the detector warranty.
Yes, when detecting on land, without any limitations. However, the detector must not be used underwater whilst charging or when connected to a power bank.
Yes. If the detector is being used, when powered by a USB power bank, the battery may charge at a slower rate if there is enough spare capacity in the power bank.
Yes. Connecting the X-TERRA ELITE to a USB power bank will allow you to continue to use the detector even if the battery is low/flat. The power bank will charge the detector if there is any residue power to charge the battery.
예. 물속에서나 해변에서 감지한 후에는 깨끗하고 담수로 감지기를 세척하는 것이 좋습니다. 감지기를 청소할 때 연마제나 용제를 사용하지 마십시오.
탐지기를 수중 세척할 때마다 항상 제어 포드 후면의 플라스틱 마개가 헤드폰 잭에 나사로 단단히 고정되어 있는지 확인하십시오.
No. It is not necessary to lubricate or grease any part of the detector, including the waterproof seals. Using any petroleum-based grease will damage the waterproof seals and void the warranty.
If deep wading or fully submerged, we recommend using only Minelab Waterproof Headphones. These have a specially engineered connector that forms a waterproof seal when used with the X-TERRA ELITE.
VANQUISH depth performance is similar but not quite as deep as the EQUINOX. However, EQUINOX detectors are more configurable for varying conditions.
Minelab does not publish the exact frequencies of Multi-IQ technology used in the VANQUISH Series. These frequencies are similar to the Multi-IQ mode in the EQUINOX Series.
The VANQUISH Series detectors only use Multi-IQ (simultaneous multi-frequency) technology.
Target IDs on VANQUISH are the same as the Target IDs on EQUINOX.
Recovery speed varies depending on the mode selected.
The Custom mode is programmable. If you program custom mode, it will adopt the recovery speed from the mode you program it to, e.g. coin mode = fast recovery speed, jewellery = medium recovery speed, relic = slow recovery speed.
When the detector is switched off, discrimination patterns in coin, jewellery & relic modes are all reset. Custom mode will keep its saved discrimination pattern.
There are three coils available for VANQUISH. These are:
The VANQUISH Series requires x4 AA batteries and is compatible with both rechargeable and non-rechargeable batteries. The battery level indicator shows the current battery level. Lift the battery cover off the control box to replace the batteries.
The VANQUISH 540 and 540 Pro-Pack come with x4 AA NiMH rechargeable cells and a charger. The VANQUISH 340 and 440 can also operate with rechargeable batteries. Minelab recommends only NiMH rechargeable batteries or non-rechargeable AA alkaline batteries. Batteries rated between 1.2v – 1.5v are acceptable. If the battery has a voltage higher than 1.5v, it can damage the detector.
AA rechargeable NiMH batteries provide a run-time of approximately 11 hours using factory default settings.
Non-rechargeable, high-quality AA alkaline batteries provide a run-time of approximately 10 hours.
No. VANQUISH coils cannot be used on EQUINOX, and EQUINOX coils cannot be used on VANQUISH.
The VANQUISH control box is not submersible. The coils are fully waterproof up to 1 m (3 ft).
The temperature specification for the VANQUISH Series is -10C – 40 C (14F – 104 F). The coil is waterproof to 1 m (3 ft), but the control pod cannot be submerged.
No. Pitch or tone breakpoints cannot be adjusted on the VANQUISH Series.
The VANQUISH 540 has a red backlight for detecting in low light situations. The backlight is 'Off' by default at each start-up to reduce battery consumption.
The Multi-IQ technology used in VANQUISH allows the detector to provide stable and reliable target IDs in light of medium mineralised soils found in beaches or parks. As a result, there is no ground balance function available in the VANQUISH Series.
Multi-IQ technology allows VANQUISH to operate on wet beach sand and salt water with much higher performance than a single frequency VLF detector.
VANQUISH 540 can operate with Bluetooth V4.2 or later and Bluetooth aptX Low Latency headphones. VANQUISH 340 & 440 do not have wireless capability.
Yes. Software updates can be found on the Minelab website on the VANQUISH product page 'downloads' section.
VANQUISH Series detectors are under warranty for three years (36 months) from the Date of Purchase. Detailed product warranty information can be found under SUPPORT at minelab.com.
Including battery weight, the VANQUISH 340 and 440 weigh 1.2 kg (2.6 lbs), whereas VANQUISH 540 weighs 1.3 kg (2.9 lbs), as it includes the larger V12 coil.
VANQUISH 540 Pro-Pack contains the same VANQUISH 540 detector but includes the smaller V8 coil and the ML80 Bluetooth aptX Low Latency wireless headphones.
감지기를 끈 후 감지기를 다시 시작하기 전에 최소 2초 동안 기다리십시오.
Iron Bias 설정은 모든 VANQUISH 감지기의 모든 모드에서 동일합니다.
참고: VANQUISH 540에는 EQUINOX와 유사한 철 바이어스 응답을 갖는 조정 가능한 철 바이어스가 있습니다.
PRO-SWITCH technology is a single frequency VLF technology that allows the user to switch transmit frequencies at the touch of a button to optimise performance.
Changing frequency gives detectorists the ability to adjust frequencies to move away from noise or optimise detection ability when hunting for specific metal targets.
Park and Field modes have 5kHz, 10kHz and 15kHz selectable frequencies. Beach modes have an 8kHz single frequency for high salt mineralisation.
MULTI-IQ will provide superior results when compared to PRO-SWITCH. There may be situations where the PRO-SWITCH technology can perform equally as well as MULTI-IQ. This will depend on how the user has optimised the detector settings.
Multi-IQ will provide maximum performance in all situations as the internal processor does all the hard work. PRO-SWITCH relies on the user to ensure the detector is set to its optimal performance capability.
VANQUISH detectors with MULTI-IQ are a switch-on and go type detector designed to have excellent performance but still be very easy to use with minimal setting adjustments. This is possible as the MULTI-IQ processor does all the hard work for you.
X-TERRA PRO is a high performing single frequency detector designed for the more committed detectorist looking for a well-priced detector with great performance. Users have the ability to adjust transmit frequency which provides more control allowing detectorists to tune the detection performance when hunting for specific targets. The X-TERRA PRO is waterproof to 5 meters (15 feet) and provides superior performance when compared to any other single frequency detector currently on the market.
Target ID’s on the X-TERRA PRO will generally not be quite as stable as MULTI-IQ target ID’s and MULTI-IQ detectors will generally provide superior performance when in conductive (salty) soils.
The X-TERRA PRO comes with a V12X 12” Elliptical Double-D coil in the box, you can purchase the below accessory coils from your local Minelab dealership. Any coil that is compatible with the EQUINOX detectors is also compatible with the X-TERRA PRO.
10kHz is the best all-round frequency to start detecting with as it provides good depth and sensitivity across a range of different targets.
It is expected when running a lower transmit frequency on the X-TERRA PRO that performance on high conductors containing silver or copper will provide similar depths to MULTI-IQ detectors.
It is expected when running a higher transmit frequency on the X-TERRA PRO that performance on lower conductors containing gold will provide similar depths to MULTI-IQ detectors.
At the beach in salty conditions most single frequency detectors struggle with the mineralisation. The X-TERRA PRO provides unprecedented performance for a single frequency VLF detector in salty conditions.
Yes, there is no need to perform a full factory reset. Individual Search Profiles can easily be returned to their factory preset settings. Only the local settings will be reset and any global settings will remain in their last-use state.
Yes, you can purchase the Minelab ML85 headphones, ML105 headphones or the WM09 wireless module. These are all compatible with the X-TERRA PRO.
There are currently no aftermarket wireless headphones available for the X-TERRA PRO.
The X-TERRA PRO uses a proprietary wireless audio that is not compatible with any current versions of BLUETOOTH. The Minelab ML85 or ML105 headphones and WM09 wireless module are compatible with the X-TERRA PRO and are available from your local authorised Minelab dealership.
Park 1 provides a default 10kHz transmit frequency and is optimised for detecting modern coins and larger jewellery. This is a good mode to learn the X-TERRA PRO before experimenting with other settings.
Park 2 provides a default 15kHz transmit frequency and is optimised for detecting fine jewellery and smaller targets in trash infested areas. Recovery speed in Park 2 is increased to clearly identify good targets masked by iron trash.
Field 1 provides a default 10kHz transmit frequency and is optimised for detecting modern coins and general detecting. It has a high trash rejection which makes it an ideal detect mode for areas containing coke.
Field 2 provides a default 15kHz transmit frequency and is optimised for locations with high target and trash densities. This mode is great for coins on edge or sitting at greater depths. It has a high trash rejection which makes it an ideal detect mode for areas containing coke.
Beach 1 provides a default 8kHz transmit frequency and is optimised for dry and wet sand. Beach 1 mode has a lower recovery speed for better depth across all targets and is good for detecting coins and small to large jewellery.
Beach 2 provides a default 8kHz transmit frequency and is optimised for underwater usage where a very strong salt signal is present. To compensate for the high salt content Beach 2 has a lower transmit power. Beach 2 has a higher recovery speed to aid in saltwater rejection. It can also be used in dry soils that are conductive (salty).
Typical runtime, from a full charge using wired headphones, is approximately 16 hours. The X-TERRA PRO detector can also be powered directly from any USB Power Bank that supports 0.5A or 2A (@ 5V) output capability. This effectively gives a continuous runtime only limited by the capacity of the power bank.
The X-TERRA PRO detector supports charging from devices that comply to the USB 2.0 standard. QuickCharge™ is a proprietary standard develop by Qualcomm that uses a higher voltage and is not compatible with X-TERRA PRO detectors.
The charge time, from completely flat to 100%, is approximately 4 hours when charged with a high capacity charger (>1.7A @ 5V).
Longevity for all batteries depends on a number of factors that are often controllable to some degree by the user; such as temperature, charge levels when stored, charge cycles etc. The most common cause of reduced life of Li-ION batteries is keeping a fully charged battery at elevated temperatures.
As with all components used in our detectors, we stringently source only modern high quality components from responsible vendors. We do not expect users to experience any battery issues over years of use. Our experience with the CTX 3030 and GPZ 7000 detectors which both use Li-ION batteries is that the vast majority of users have never needed to purchase a replacement battery.
Use only reputable and certified USB Chargers when charging the X-TERRA PRO battery as detailed below:
핸들에 포함된 리튬 이온 배터리는 교체가 가능하며 보증 기간이 적용됩니다. 구입일로부터 6 개월. Minelab에서는 방수 씰의 손상 가능성과 감지기 보증 무효화를 방지하기 위해 공인 서비스 센터를 이용할 것을 권장합니다.
Yes, when detecting on land, without any limitations. However, the detector must not be used underwater whilst charging or when connected to a power bank.
Yes. If the detector is being used, when powered by a USB power bank, the battery may charge at a slower rate if there is enough spare capacity in the power bank.
Yes. It is good practice to wash the detector with clean fresh water after detecting in water or on the beach. Never use abrasives or solvents to clean the detector.
Whenever washing or using your detector underwater always ensure that the plastic bung on the rear of the control pod is firmly screwed into the headphone jack.
No. It is not necessary to lubricate or grease any part of the detector, including the waterproof seals. Using any petroleum-based grease will damage the waterproof seals and void the warranty.
If deep wading or fully submerged, we recommend using only Minelab Waterproof Headphones. These have a specially engineered connector that forms a waterproof seal when used with the X-TERRA PRO. These headphones are available as an accessory (Part Number: 3011-0372)
No, the detection coil that is included with your GO-FIND detector is designed to provide the best performance for that specific model and cannot be changed.
The battery compartment is in the handle of the GO-FIND. On the rear of the handle, you will see a small tab. Gently pull this tab down and then lift the battery compartment lid to access the batteries.
Yes, the GO-FIND series can operate with rechargeable 1.2volt Ni-MH rechargeable batteries. You can only use batteries that have a 1.2 volt or 1.5volt rating. Most AA Lithium batteries have a higher voltage and cannot be used as they exceed the maximum voltage rating for the detector. Using Lithium batteries that exceed the maximum voltage rating can damage the internal electronics of the detector. This type of damage is not covered under warranty.
The detection coil on the GO-FIND series is waterproof to 60cm (2ft) and can be washed. The screen pod should never be washed or submerged in water as it is not waterproof. To clean the screen pod wipe it with a damp cloth.
Yes, the GO-FIND detectors utilise Minelab’s Easy-Trak ground balance technology which automatically senses salt mineralisation in the ground and adjusts the detector to ensure constant smooth usage when detecting in beaches or parks.
Wireless headphones can be used but they cannot be paired directly to your detector. You will need to connect your wireless headphones to your smartphone and then connect your GO-FIND 44 or 66 to your smartphone via the GO-FIND app. GO-FIND 11 or 22 do not have Bluetooth capability and cannot connect to the GO-FIND app or wireless headphones.
In your Android phone Google Play Store & Apple iPhone App Store Search for Minelab GO-FIND
GO-FIND by Minelab Electronics Pty Ltd will be 1st – 2nd in search result.
The Pro App function is FREE for GO-FIND 66 detectors. Download the same GO-FIND App for FREE. When this GO-FIND App is paired with a GO-FIND 66, the App will activate full Pro App functions.
Download the same GO-FIND App for FREE. When this GO-FIND App is paired with a GO-FIND 44, the App will activate basic App functions.
Download the same GO-FIND App for FREE. When this GO-FIND App is paired with a GO-FIND 44, the App will activate basic App functions. It is optional to upgrade your Basic App functions to Pro App functions, just like how it used on a GO-FIND 66. In-app purchase is available for upgrading.
For the first time use, you need to pair GO-FIND 44/66 with your mobile device:
See also:
In GO-FIND App, the is help (?) button on the bottom right corner. Click to view Bluetooth pairing guide and Bluetooth connection guide.
No, after the pairing for the first time use. Your next time use should just require a short press to turn on Bluetooth function.
You can now use App with the detector
Android 11 or later with Bluetooth Lower Energy hardware
iPhone iOS 8.0 or later with Bluetooth Lower Energy hardware
No, the X-TERRA VOYAGER uses different technology to other detectors. You can only use the coil that is supplied in the box with the detector.
The X-TERRA VOYAGER does not have any accessory coils currently available.
The depth gauge will provide an approximate indication of depth and should only be used as a guide as large or small metals will cause the gauge to become inaccurate. A coin sized object will provide the below estimated depths.
1 arrow = 1” (25mm)
2 arrows = 3” (75mm)
3 arrows = 5” (125mm)
4 arrows = 6” (150mm)
5 arrows = >6” (>150mm)
The X-TERRA VOYAGER does not have wireless capability. You can use a Bluetooth wireless transmit module with the detector. These are not available from Minelab and will have to be purchased separately.
All Metal allows the detector to detect all metal types. When in all metal mode there will be no discrimination of any metal types.
Custom provides users the ability to discriminate any of the target group icons at the top of the screen. You simply navigate through to the desired target group and the icon will flash for a few seconds and then it will disappear. All target ID’s in this target group will now be discriminated out.
To detect the discriminated target group simply navigate away from the target group and then navigate back to the desired target group. The icon will flash for a few seconds and then appear. All target ID’s in the target group will now detect again.
Jewelry provides discrimination pattern that ignores most iron/ferrous junk. You will also find coins, relics and other non-ferrous metals. This mode is good for trashy environments.
Learn allows users to detect 1 specific target group. You simply need to wave the desired metal over the detection coil, the detector will then learn this target ID and accept only targets ID’s within that target group.
Typical runtime, when using new high quality 9-volt alkaline batteries is 20 hours.
It is good practice to clean your detector after each use. Only fresh water should be used when cleaning. Never use abrasives or solvents to clean the detector. The detection coil is waterproof and can be washed with the hose. The Screen pod should only be carefully wiped with a clean damp cloth to avoid any water or moisture ingress.
No. It is not necessary to lubricate or grease any part of the detector. Using any petroleum-based grease can damage the plastics and void the warranty.
To disable the audio tones, you simply need to push and hold the "minus" button when powering the PRO-FIND 40 on.
To enable the audio tones, you simply need to push and hold the "plus" button when powering the PRO-FIND 40 on.
To disable the ferrous tones OFF simply push and hold the "minus" button when the PRO-FIND 40 is powered on and then wait for the long beep.
To enable the ferrous tones ON simply push and hold the "plus" button when the PRO-FIND 40 is powered on and then wait for the long beep.
No, the LED flashlight cannot be adjusted.
No, the vibration cannot be toggled ON/OFF.
The Rapid Re-tune feature was designed so that users do not have to power cycle the pin-pointers to re-tune the PRO-FIND to the environment.
To re-tune the PRO-FIND 40 simply short-press the power button when the PRO-FIND 40 is powered on.
At maximum Sensitivity the PRO-FIND 40 can detect targets at greater distances which can be both an advantage and a disadvantage. To pinpoint a target sometimes it’s better to have a less sensitive probe to reduce the search area, so we have given you the ability to adjust it how you see fit. The Sensitivity may also need to be reduced in mineralised or salty soils, so that you are only detecting metal and not the minerals in the ground.
Side detection occurring with the target (or multiple) in the side of the hole. Use the tip of the probe to check around the sides of the hole. Reducing the Sensitivity can also help.
Yes, but be aware that the PRO-FIND 40 won’t have the same sensitivity to very small nuggets as a quality Minelab metal detector. It will be a good aid in target recovery for larger nuggets.
Yes, the PRO-FIND 40 is waterproof to 3 meters (10ft) and can be washed. When washing always use clean fresh water.
If no targets are detected or buttons pressed for 5 minutes, then the PRO-FIND 40 will start a slow constant beep (Lost Alarm) this alarm will sound for 5 minutes and then the PRO-FIND 40 will power off to save battery life.
The battery may be flat or inserted incorrectly. Replace the battery and/or check the battery orientation. If you are still having issues, contact your closest Minelab Service Centre.
The PRO-FIND 40 has a 3rd beep that notifies you that the pin-pointer has calibrated to the environment. This can sometimes take up to 30 seconds to occur depending on environmental conditions. You can short press the power button to perform a rapid re-tune. You should then hear a confirmation beep and the PRO-FIND 40 should now detect metals.
Tips for switching on:
*Calibration usually takes less than a second when the unit has been used recently.*
In highly mineralised soils:
대상이 감지되지 않거나 몇 분 동안 버튼을 누르면 장치에서 알람이 울리기 시작하여 긴 신호음이 울리므로 핀 포인터를 찾을 수 있습니다. 몇 분 후 배터리 수명을 유지하기 위해 핀 포인터가 자동으로 꺼집니다.
구멍을 파고 땅에 남겨두면 장치를 찾을 수 있습니다. 진동 전용 모드 인 경우 경고음이 발생하지 않습니다. 5 분 동안 느린 경고음이 울리면 기기가 자동으로 꺼집니다.
뚜껑이 켜지면 배터리가 잘못된 방식으로 삽입되어있을 수 있지만 조이기는 어렵습니다. 열쇠 형 플라스틱은 배터리 탭이 접점에 닿지 않도록합니다. 배터리를 돌려서이 문제를 해결하십시오.
Pro-Find를 켜면 2 번의 삐 소리가 나고 3 번 더 짧은 삐 소리가납니다. 이 교정은 때때로 15-20 초가 소요될 수 있습니다. Pro-Find를 금속 물체 근처에두기 전에이 교정 경고음이 발생할 때까지 기다리십시오. 스위치를 켤 때 금속 근처에 Pro-Find가 있으면 보정되지 않으며 Pro-Find를 다시 시작해야합니다.
구멍의 측면에서 대상 (또는 여러 개)으로 발생하는 측면 감지 구멍 끝을 확인하기 위해 프로브의 끝을 사용하십시오. 감도를 줄이는 것도 도움이 될 수 있습니다.
예, 그러나 품질이 우수한 Minelab Gold Detector와 같은 초소형 덩어리에 대해 동일한 감도를 갖지 않습니다. 더 큰 덩어리의 대상 복구에 도움이 될 것입니다.
최대 감도에서 PRO-FIND 35는 장거리에서 대상을 감지 할 수있어 장단점이 될 수 있습니다. 때때로 대상을 정확히 찾아 내려면 검색 영역을 줄이기 위해 덜 민감한 프로브를 사용하는 것이 좋습니다. 따라서 원하는대로 조정하는 기능을 제공했습니다. 광물성 또는 짠 토양에서는 감도를 줄여야 만 땅이 아닌 금속 만 감지 할 수 있습니다.
PRO-FIND 35는 3 미터까지 완벽하게 방수되므로 핀 포인터를 물에 담그면 청소할 수 있습니다. 핀 포인터를 담그기 전에 배터리 캡이 완전히 조여져 있는지 확인하십시오.
PRO-FIND 15는 방수 기능 만 있습니다. 엄지 손가락으로 스피커 통풍구를 막 으면 흐르는 물로 씻을 수 있습니다.
켜기 팁 :
기기를 최근에 사용한 경우 일반적으로 교정에 1 초 미만
고도로 광물 화 된 토양에서 :
오디오 켜기 및 끄기 (Pro-Find 35 만 해당) :
철음 켜짐 및 꺼짐 (Pro-Find 35 만 해당) :
CTX 3030, GPZ 7000 및 XChange 2는 모두 데이터 저장을 위해 SQLite를 사용합니다. SQLiteSpy 와 같은 도구를 사용하면 파일을 추출하는 데 도움이 될 수 있습니다. 추출된 파일이 직접 실행되므로 SQLiteSpy를 설치할 필요가 없습니다.
1. 탐지기를 PC에 연결하고 생성된 새 이동식 드라이브로 이동합니다.
2. 드라이브를 엽니다.
3. 내부에 파일이 있습니다. 이것을 사용할 위치에 복사하십시오. 이 파일은 열어야 하는 저장소 데이터베이스입니다.
1. XChange 2에서 추출하려는 포인트를 선택하십시오.
2. "파일"폴더로 드래그합니다.
3. '파일'폴더를 클릭하여 엽니 다.
4. 'Minelab 파일 내보내기'버튼을 클릭합니다.
5. 파일은 '다운로드'폴더에 있어야합니다.
6. 다운로드 한이 파일은 압축되어 있으므로 7zip과 같은 도구를 사용하여 내부의 'shareData'파일을 추출해야합니다.
7. 'shareData'를 사용할 위치에 복사합니다. 이 파일은 열어야하는 스토리지 데이터베이스에 있습니다.
이 예제에서는 SQLiteSpy가 사용되지만 다른 도구에도 적용되는 유사한 프로세스입니다.
1. SQLiteSpy 열기
2. '파일'> '데이터베이스 열기 ...'를 선택하십시오.
3. 데이터베이스 위치로 이동합니다.
4. 파일 형식을 '모든 파일 (*. *)'로 변경합니다.
5. 데이터베이스를 선택하고 '열기'를 선택합니다.
6. 왼쪽에는 사용 된 데이터베이스 파일에 따라 여러 테이블이 있습니다.
ㅏ. "findpoint": 여기에는 저장된 각 FindPoint가 포함됩니다.
비. "waypoint": 여기에는 저장된 각 WayPoint가 포함됩니다.
씨. "point": 여기에는 모든 GeoHunt에서 트랙을 만드는 데 사용되는 각 지점이 포함됩니다. 각 GeoHunt는 "geohunt_fk"열에서 UUID로 식별됩니다.
디. "geohunt": 여기에는 "points"테이블에서 각 GeoHunt를 식별하는 데 사용되는 UUID가 포함됩니다.
7. 또한 일부 FindPoint를 추출한다고 가정합니다 (다른 포인트에도 동일한 절차가 사용됨).
8. "findpoint"테이블을 더블 클릭합니다. 추출 된 모든 FindPoint가 표시됩니다.
9. 테이블의 행을 클릭 한 다음 "Ctrl + A"키를 눌러 모든 행을 선택합니다.
10. "Ctrl + C"키를 눌러 모든 데이터를 복사합니다.
11. 엑셀 열기
12. 데이터를 스프레드 시트에 붙여 넣습니다.
13. 일부 데이터베이스 파일에서는 위도와 경도를 10,000,000으로 나누어 올바른 형식으로 사용해야합니다.
14. 여기에서 포인트로 필요한 작업을 수행하십시오.
